THE FOUNDATION OF PLUMBING SKILLS WHEN INSTALLING A BATHTUB

The Foundation of Plumbing Skills When Installing a Bathtub

The Foundation of Plumbing Skills When Installing a Bathtub

Blog Article

Call

We have noticed this post relating to A Step-by-Step Guide to Installing a Bathtub directly below on the web and decided it made perfect sense to discuss it with you here.


How to Install a Bathtub Yourself
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is conveniently obtainable, the job can relocate speedily; if you have to open a wall surface to remove the old bathtub and also place the new tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to vacate the old bathtub and also embeded in the brand-new one. Ensure you have actually certified on your own for the work as well as are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed project, it is much better to consider utilizing one before you start. Opportunities are you may require a professional plumber to make tube connections.
This short article will certainly assist you mount a brand-new bathtub in your restroom if you have already acquired a new bathtub and also do not need to alter the arrangement of your previous water pipelines.
Your tools as well as product checklist ought to comprise the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Planning for the Setup


    To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to prevent strain on the bath tub.
    Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you use all of the provided washing machines.
    Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its last placement.

    Removing Old Touches


    If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you must do is separate the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the limited accessibility that is frequently the instance.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have actually been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
    Before proceeding to fit the new faucets, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

    Mounting the Bathtub


    Utilizing the two wooden boards under its feet, put the bathtub in the needed setting. The wooden boards are helpful in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
    The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level and also readjusting the feet on the bath tub until the spirit level reviews level.
    To mount taps, fit the bottom of the furthest adaptable tap adapter to the proper supply pipe by making a compression join; after that do the same for the other faucet.
    Switch on the water and also inspect all joints and new pipework for leaks and also tighten them if needed. Fill up the bath tub as well as additionally check the overflow electrical outlet and also the regular outlet for leaks.
    Ultimately, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bath tub ought to wait up until the bath tub has actually been utilized at least when as this will settle it right into its final setting.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, then you will need a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipelines.
    If you require to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Protect the faucet in place with the producer provided backnut. Once the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former type should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Tub


    In the area where the bathroom fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a rigid seal, causing the water to penetrate the wall in between the bath and the tiling, bring about issues with dampness as well as feasible leaks to the ceiling below.
    You can select from a selection of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to enable the movement experienced when the bathtub remains in use. The sealant can break rather very early if you do not take into account this activity before securing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water-proof glue and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I hope you enjoyed reading our post about How to Install a Bathtub. Thanks a lot for spending some time to browse our article. Appreciated our review? Please share it. Let someone else locate it. Many thanks for taking the time to read it.


    Certified emergency plumbing assistance available.

    Report this page